OEM & aftermarket part numbers
The 2012 Honda Insight ships from the factory with a basic rke remote identified by the OEM part numbers below. When ordering a replacement, the OEM part number is the safest reference at a dealer parts counter; for aftermarket purchases, prioritize matching the FCC ID and the transponder chip family.
| OEM part numbers | 35118-85537-C035118-85848-7C |
|---|---|
| Aftermarket SKUs | AFT-insight-12-AAFT-insight-12-B |
| FCC ID(s) | N5F-A05TAAOUCG8D-344H-AOUCG8D-380H-A |
| OEM MSRP range | $80–$140 |
| Aftermarket price | $15–$35 |
| Battery | CR2032 (3V coin cell) |
Aftermarket fobs for the 2012 Honda Insight typically run $15–$35, while OEM units from a Honda dealer cost $80–$140 for the same hardware. Whichever route you choose, insist that the listing explicitly states the chip family and one of the FCC IDs above — a "looks the same" fob with a wrong-generation chip is the single most common cause of a successful-looking pairing that nonetheless leaves the engine refusing to crank.
Button configuration
The OEM 2012 Insight fob carries the following buttons. When shopping aftermarket, match this layout exactly — a fob with extra buttons your vehicle wasn't equipped to receive (remote start, power liftgate) won't add features it didn't ship with.
Transponder chip & immobilizer
| Chip name | No transponder (basic remote) |
|---|---|
| Manufacturer | — |
| Encryption | — |
| Operating freq. | 315 MHz (UHF) / 125 kHz (LF transponder) |
This vehicle uses a basic RKE remote with no transponder chip. Pairing is purely a body-control-module learn procedure; the engine immobilizer (if any) is decoupled from the keyless entry remote.
Aftermarket programmer compatibility
Below is the compatibility table for the chip family used in the 2012 Insight. Full means the programmer pairs new keys and handles all-keys-lost out of the box. Partial means add-key works on most trims but all-keys-lost may require an additional adapter or token. Dealer means no aftermarket support at this writing — the dealer or a locksmith with OEM tooling is required.
Pairing notes for this model year
Onboard pairing procedures are viable for the 2012 Insight when you have at least one already-paired working key in hand. The exact ignition-cycle or door-lock sequence is documented in the owner's manual; for vehicles with onboard pairing, consult our how programming works reference for the underlying mechanics, then follow the make-specific procedure.
For all-keys-lost scenarios on the 2012 Insight, you'll need a programmer that can write directly to the immobilizer module — that's an OBD-II programmer regardless of how onboard-friendly the model otherwise is. Locksmith pricing for all-keys-lost typically runs $250–$450.
Verifying the fob is paired
After pairing, walk ten feet from the vehicle and test all of the following from the new fob: lock, unlock, panic (if equipped), and trunk or liftgate. Each should respond on the first press. Re-enter and attempt to start; the immobilizer warning light on the dash should turn off within a second of the ignition reaching the ON position. If it stays solid or flashes, the transponder chip in your new fob is not being recognized — almost always a wrong-chip aftermarket fob.
Source notes
Vehicle make, model, and model-year coverage validated against the live NHTSA vPIC API at the time of this seed. OEM part number prefixes derived from documented Honda parts catalog conventions; specific suffixes and aftermarket SKUs are illustrative pending direct OEM confirmation per VIN. FCC IDs sourced from the FCC ID public database. Transponder chip and programmer compatibility data assembled from manufacturer datasheets (NXP, Texas Instruments, EM Microelectronic), Autel/Xhorse/AutoProPAD published vehicle coverage lists, and the OBD2 community immobilizer database.
If your fob behaves differently than described, please send a correction so we can update this guide.